等温退火对8030铝合金导线组织性能的影响

研究了不同等温退火工艺对8030铝合金导线组织及性能的影响。结果表明:等温退火前后合金均由α-Al基体和Al₆Fe相组成。在同一等温温度下,随着等温时间的延长组织逐渐趋于均匀化;同一等温时间下,随着等温温度的升高,组织趋于均匀化的时间缩短。经过等温退火处理后铝合金导线的导电率均有所提高,在470 ℃均匀化退火24 h后再经240 ℃等温4 h,合金导电率达到最高值57.21%IACS,比未经热处理试样的导电率提高了2.4%IACS。经过等温退火处理后铝合金导线的硬度及抗拉强度均有所降低,塑性大幅度提高。在470 ℃均匀化退火24 h后再经260 ℃等温8 h,合金的伸长率最高可达23.64%。热处理前后合金均为塑性断裂。     

Structure,properties, and applications of polyacrylonitrile/carbon nanotube (CNT) fibers at low CNT loading

Bi-component, polyacrylonitrile (PAN)/carbon nanotube (CNT) fibers were processed, at different core-sheath area ratios, by gel spinning. A percolated CNT network at 10 wt% CNT in the sheath enhanced electrical conductivity as compared to the neat PAN fiber, while PAN polymer in the core contributed to the good mechanical properties. Fibers with relatively thin sheath allowed overall CNT loading as low as 3.7 wt% to be made with good electrical conductivity, and PAN stabilization by Joule heating was demonstrated. Such fibers with combined good mechanical properties and electrical conductivity can also potentially be used for electrical heating of fabrics, for making smart textiles, and for electromagnetic interference shielding.     

具有高耐蚀性和导电性的掺Cr类金刚石非晶碳的化学式解析

Cr掺杂的类金刚石非晶碳具有良好的导电性和耐腐蚀性,这对于燃料电池金属双极板涂层改性特别重要。使用团簇加连接原子模型对其非晶结构进行了详细解析,在该模型中,良好的玻璃形成材料由覆盖特征性最近邻团簇加上几个下一壳层原子的结构单元来表述。根据文献,在Cr掺杂的类金刚石非晶碳中占优势的团簇是Cr中心和C壳层的[Cr-C4]四面体团簇,然后将该团簇与适当的连接原子匹配,以满足电子轨道饱和原理。由此推导出了两个最优组成式,即[Cr-C4]CrC3(22.2%Cr)和[Cr-C4]Cr3C2(40%Cr),它们显示出良好的非晶态结构稳定性。实验结果显示,所提出的这两组化学组成的涂层材料兼具低电阻率(低至10-4Ω·cm)和优异的耐腐蚀性(腐蚀电流密度~10^-2μA/cm^2)。在sp2键含量和渗流理论的框架内讨论了导电和耐蚀的协同行为。这项工作验证了团簇加连接原子模型在具有高耐腐蚀性和高导电性的涂层材料成分设计中的可行性。     

Novel thermal-sensitive properties of NBT-BZT composite ceramics for high-temperature NTC thermistors

We found for the first time that (1 − x) Na_0.5Bi_0.5TiO₃-xBiZn_0.5Ti_0.5O₃ (NBT–BZT) composite ceramics showed negative temperature coefficient (NTC) at a high temperature. The NBT–BZT nanopowders were successfully prepared by Pechini method. Their ceramics were sintered at 1100°C. The NBT–BZT ceramic exhibited a good linear relationship between logarithm of electrical resistivity (Inρ) and reciprocal of absolute temperature (1000/T) at 250°C–1050°C. The obtained ρ₆₀₀, ρ₉₀₀, and B_600/900 constants of the NBT–ZBT NTC thermistors are approximately 5.92 × 10⁶ to 3.01 × 10⁴ Ω cm, 7.03 × 10³ to 7.60 × 10² Ω cm and 2.3 × 10⁴-1.3 × 10⁴ K, respectively. The electrical characteristics can be tuned to the desired value by changing the Na_0.5Bi_0.5TiO₃ content in the compound. The electrical conductivity in these compounds is due to the electron jumps between Ti³⁺ and Ti⁴⁺ and oxygen-ion conductivity. Results demonstrate a tremendous potential of the studied system for perovskite materials with NTC performance.     

Correlation between B value deviation and sintering temperature of perovskite solid solution materials

The effects of different sintering temperatures on the system of Ba_0.5Sr_0.5TiO₃–La_0.8Ca_0.2MnO₃ (BST-LCM) material were investigated by means of scanning electron microscopy, X-ray, resistance-temperature measurements, and X-ray photoelectron spectroscopy. X-ray diffraction and X-ray photoelectron spectroscopy confirm that BST-LCM is completely miscible and BST is the main phase, which under the premise of following the theory of small polaron conduction, titanium ions interact with manganese ions, which affects the electrical properties of the system of BST-LCM material. For the electrical properties of related, the LCM content is inversely proportional to the activation energy. Through the linear fitting of the experimental data, the empirical formula between the sintering temperature B value and the content of solid solution is obtained, and the approximate B value within a certain range can be preliminarily calculated.     

Electrical and mechanical properties of BZT − xBCT lead-free piezoceramics

In this study, lead-free (1 − x)Ba(Zr_0.2Ti_0.8)O₃ − x(Ba_0.7Ca_0.3)TiO₃ compositions are synthesized via conventional solid oxide route, and the ceramics are fabricated with normal sintering in air. The effects of composition fluctuations on dielectric, piezoelectric, and mechanical properties are investigated. The phase structure and the microstructure are analyzed with X-ray diffraction and scanning electron microscopy. The best dielectric and piezoelectric properties of ε_r = 11 207 and d₃₃ = 330 pC/N were obtained for BZT−0.35BCT and BZT−0.5BCT ceramics, respectively. The mechanical behavior—in terms of Vickers hardness and compressive and flexural strengths—was investigated, and the best mechanical behavior was found in the vicinity of the phase transition boundary with x values between 0.5 and 0.6.     

Hierarchical micro-nanostructured albite-based glass-ceramic for high dielectric strength insulators

A novel glass-ceramic material based on albite type Na-rich feldspar has been synthesized by conventional ceramic process. High crystallinity, >94%?Vol.% is obtained by fast sintering which allows energy saving processing. Albite is the main crystalline phase and tetragonal SiO₂ is a secondary phase. Electrical properties were examined by complex impedance, DC measurements, and dielectric breakdown test. Dielectric characterization shows a non-Debye type dielectric behavior with low dielectric constant, 4.6 at 1?MHz, low dielectric losses, (～10^?3 at 1?MHz, and a large dielectric strength, ～60?kV/mm), that it is the largest value reported in ceramic insulators. Those dielectric properties are attained by the low glassy phase content in the samples and their unique micro-nanostructure. All these properties make this novel material a very promising candidate in the market of ceramic electrical insulator, highlighting for high-voltage applications.     

Morphology,mechanical properties and electromagnetic shielding effectiveness of poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene)/carbon nanotube nanocomposites: effects of maleic anhydride,carbon nanotube loading and processing method

Nanocomposites based on poly(styrene‐b‐ethylene‐ran‐butylene‐b‐styrene) (SEBS) and carbon nanotubes (CNTs) (SEBS/CNT) as well as SEBS grafted with maleic anhydride (SEBS‐MA)/CNT were successfully prepared for electromagnetic shielding applications. Both SEBS/CNT and SEBS‐MA/CNT nanocomposites were prepared by melt compounding and were post‐processed using two different techniques: tape extrusion and compression moulding. The different nanocomposites were characterized by Raman spectroscopy and rheological analysis. Their mechanical properties, electrical properties (10^-2–10⁵ Hz) and electromagnetic shielding effectiveness (8.2–12.4 GHz) were also evaluated. The results showed that the CNT loading amount, the presence of MA in the matrix and the shaping technique used strongly influence the final morphologies and properties of the nanocomposites. Whilst the nanocomposite containing 8 wt% CNTs prepared by compression moulding presented the highest electromagnetic shielding effectiveness (with a value of 56.73 dB, which corresponds to an attenuation of 99.9996% of the incident radiation), the nanocomposite containing 5 wt% CNTs prepared by tape extrusion presented the best balance between electromagnetic and mechanical properties and was a good candidate to be used as an efficient flexible electromagnetic interference shielding material. © 2018 Society of Chemical Industry     

Fabrication of core–shell nanocomposites with enhanced photocatalytic efficacy

The current study establishes the unprecedented involvement in the evolution and production of novel core–shell nanocomposites composed of nanosized titanium dioxide and aniline‐o‐phenylenediamine copolymer. TiO₂@copoly(aniline and o‐phenylenediamine) (TiO₂@PANI‐o‐PDA) core–shell nanocomposites were chemically synthesized in a molar ratio of 5:1 of the particular monomers and several weights of nano‐TiO₂ via oxidative copolymerization. The construction of the TiO₂@PANI‐o‐PDA core–shell nanocomposites was ascertained from Fourier transform IR spectroscopy, UV–visible spectroscopy and XRD. A reasonable thermal behavior for the original copolymer and the TiO₂@PANI‐o‐PDA core–shell nanocomposites was investigated. The bare PANI‐o‐PDA copolymer was thermally less stable than the TiO₂@PANI‐o‐PDA nanocomposites. The core–shell feature of the nanocomposites was found to have core and shell sizes of 17 nm and 19–26 nm, respectively. In addition, it was found that the addition of a high ratio of TiO₂ nanoparticles increases the electrical conductivity and consequently lowers the electrical resistivity of the TiO₂@PANI‐o‐PDA core–shell nanocomposites. The hybrid photocatalysts exhibit a dramatic photocatalytic efficacy of methylene blue degradation under solar light irradiation. A plausible interpretation of the photocatalytic degradation results of methylene blue is also demonstrated. Our setup introduces a facile, inexpensive, unique and efficient technique for developing new core–shell nanomaterials with various required functionalities and colloidal stabilities. © 2018 Society of Chemical Industry